Mini Tower Computer

 Desktop Computer

 Small Form Factor Computer

 Ultra Small Form Factor Computer

Solid green

Power is on, and the computer is operating normally. On the desktop computer, a solid green light indicates a network connection.

No corrective action is required.

Blinking green

The computer is in a power-saving mode (Microsoft® Windows® XP).

Press the power button, move the mouse, or press a key on the keyboard to wake the computer.

Blinks green several times and then turns off

A configuration error exists.

Check the diagnostic lights to see if the specific problem is identified.

Solid yellow

The Dell Diagnostics is running a test, or a device on the system board may be faulty or incorrectly installed.

If the Dell Diagnostics is running, allow the testing to complete.

If the computer does not boot, contact Dell for technical assistance.

Blinking yellow

A power supply or system board failure has occurred.

See "Power Problems."

Solid green and a beep code during POST

A problem was detected while the BIOS was executing.

See "Beep Codes" for instructions on diagnosing the beep code. Also, check the diagnostic lights to see if the specific problem is identified.

Solid green power light and no beep code and no video during POST

The monitor or the graphics card may be faulty or incorrectly installed.

Check the diagnostic lights to see if the specific problem is identified. See "Video and Monitor Problems."

Solid green power light and no beep code but the computer locks up during POST

An integrated system board device may be faulty.

Check the diagnostic lights to see if the specific problem is identified. If the problem is not identified, contact Dell for technical assistance.

The computer is in a normal "off" condition, or a possible pre-BIOS failure has occurred.

The diagnostic lights are not lit after the computer successfully boots to the operating system.

Plug the computer into a working electrical outlet and press the power button.

A possible BIOS failure has occurred; the computer is in the recovery mode.

Run the BIOS Recovery utility, wait for recovery completion, and then restart the computer.

A possible processor failure has occurred.

Reinstall the processor and restart the computer.

Memory modules are detected, but a memory failure has occurred.

• If you have one memory module installed, reinstall it and restart the computer. (see "Memory" for instructions on how to remove and install memory modules.)
• If you have two or more memory modules installed, remove the modules, reinstall one module, and then restart the computer. If the computer starts normally, reinstall an additional module. Continue until you have identified a faulty module or reinstalled all modules without error.
• If available, install properly working memory of the same type into your computer.
• If the problem persists, contact Dell.

A possible graphics card failure has occurred.

• If the computer has a graphics card, remove the card, reinstall it, and then restart the computer.
• If the problem still exists, install a graphics card that you know works and restart the computer.
• If the problem persists or the computer has integrated graphics, contact Dell.

A possible floppy or hard drive failure has occurred.

Reseat all power and data cables and restart the computer.

A possible USB failure has occurred.

Reinstall all USB devices, check cable connections, and then restart the computer.

No memory modules are detected.

• If you have one memory module installed, reinstall it and restart the computer. (see "Memory" for instructions on how to remove and install memory modules.)
• If you have two or more memory modules installed, remove the modules, reinstall one module, and then restart the computer. If the computer starts normally, reinstall an additional module. Continue until you have identified a faulty module or reinstalled all modules without error.
• If available, install properly working memory of the same type into your computer.
• If the problem persists, contact Dell.

Memory modules are detected, but a memory configuration or compatibility error exists.

• Ensure that no special memory module/memory connector placement requirements exist.
• Verify that the memory modules that you are installing are compatible with your computer.
• If the problem persists, contact Dell.

An other failure has occurred.

This pattern also displays during System Setup and may not indicate a problem.

• Ensure that the cables are properly connected to the system board from the hard drive, CD drive, and DVD drive.
• Check the computer message that appears on your monitor screen.
• If the problem persists, contact Dell.

After POST is complete, all four diagnostic lights turn green briefly before turning off to indicate normal operating condition.

None.

1-1-2

Microprocessor register failure

1-1-3

NVRAM read/write failure

1-1-4

ROM BIOS checksum failure

1-2-1

Programmable interval timer failure

1-2-2

DMA initialization failure

1-2-3

DMA page register read/write failure

1-3

Video Memory test failure

1-3-1 through 2-4-4

Memory not being properly identified or used

3-1-1

Slave DMA register failure

3-1-2

Master DMA register failure

3-1-3

Master interrupt mask register failure

3-1-4

Slave interrupt mask register failure

3-2-2

Interrupt vector loading failure

3-2-4

Keyboard Controller test failure

3-3-1

NVRAM power loss

3-3-2

Invalid NVRAM configuration

3-3-4

Video Memory test failure

3-4-1

Screen initialization failure

3-4-2

Screen retrace failure

3-4-3

Search for video ROM failure

4-2-1

No timer tick

4-2-2

Shutdown failure

4-2-3

Gate A20 failure

4-2-4

Unexpected interrupt in protected mode

4-3-1

Memory failure above address 0FFFFh

4-3-3

Timer-chip counter 2 failure

4-3-4

Time-of-day clock stopped

4-4-1

Serial or parallel port test failure

4-4-2

Failure to decompress code to shadowed memory

4-4-3

Math-coprocessor test failure

4-4-4

Cache test failure